Cross baseBasic stand in the shape of a cross – uses one pole to support media.
TwinbaseA solid 60cm bar is positioned between the two feet to enable support of wider graphics – uses two poles to support media.
Twinbase XLAs per twinbase but 100cm bar used between feet to enable support of larger media – again uses two poles.
Square PlateA flat, more permanent alternative to the cross base.
Twin plateA flat, more permanent alternative to the twinbase.
FLEX-clip topThis clip attaches the horizontal graphic bar to the vertical poles but instead fits over the top of the vertical pole preventing it sliding down when heavy media is used.
FLEX-clip bottomUsed at the bottom of single sided displays.  Slides over the pole and can be positioned anywhere or fixed using the small grub screw to the rear.
Grip clipUsed at the bottom of double sided displays connecting a horizontal graphic bar to the vertical poles.  Uses silicone strips to keep it in place.
Single ceiling clipUse this eyeleted clip with suspension wires to hang a single sided banner.
Double ceiling clipUse this eyeleted clip with suspension wires to hang a double sided banner.
Double grip clipAllows double sided Displays to be created.  Clips over the back of a grip clip.
Wall mounting kitIncludes screws, plugs and necessary connectors to wall mount a graphic.  Use one kit every 0.6m width.
Classic pole XLComes in various heights and in 1, 2 or 3 sections depending on portability required.  Creates the Display height.
Telescopic poleSimple twist and lock mechanism allowing variable height between 135cm and 250cm.
Classic barAluminium extrusion for mounting media. Can be used with FLEX-tape or Hook & Loop tape depending upon media being used.
Snaplock barAluminium extrusion with mechanical action.  Used for mounting media (without the need for tape) by trapping within its jaws.
Flexible Display connectorAllows two single Displays of the same height to be joined at an angle.
Display connector clipUse this clip to span two displays to either connect them or to stabilise a widescreen joint when it is used for straight displays.
Wide screen jointUse this to make Displays greater than 2m wide with one piece graphic drops.  It allows graphics to be used straight or angled and enables them to be folded away compactly

Display Banners

There is much more to FLEX display banners compared to the average ‘roller banner’.
Some of the main advantages:

  • Lightweight & portable
  • Highly adaptable
  • Customizable
  • Quality printed fabric graphics

From miniature table-top banners, to huge portable fabric backdrops.

Quick links:
Banner Stands up to 2m wide
Fabric Backdrops
Hanging & Mounting
View the Printed Fabric
Combine Stands Together

Main Features:

Lightweight & Portable

Aluminium construction, fabric graphics and soft carry cases mean that complete FLEX-display systems can weigh as little as 1.5kgs.
This is a huge benefit over conventional roller banners which are very heavy in comparison (~6kg) and take up more room.

Many international travellers choose our banners because the smaller banners can fit in a suitcase.

Easy assembly – You don’t need to wrestle with FLEX-display! A few simple parts clicked together and you are done.
Set up of a Cross Base banner can be easily performed in under 30 seconds. Set up is in minutes for even the biggest displays where two people are needed.

Lightweight & Portable Sisplays
Fabric Backdrops – Large Displays

Single piece graphics upto 6m x 2m – no joints or alignment issues – just one huge fabric print!
These backdrops are a great alternative to ‘pop up display’ systems which are heavy, bulky and take a relatively large amounts of time to set up – whereas the large FLEX display banners can be assembled within 5 minutes.Standard sizes are 2m, 3m, 4.5m and 6m wide by 2m tall. Custom sizes can be easily created.

Huge displays possible
Highly Adaptable & Customizable

The FLEX display components allow banner stands to be altered in different ways to suit a certain purpose…
This size of individual displays can be chosen to suit, and these banners can be linked together to create a larger display or used separately when needed.
Our floor standing banners can also be easily mounted on a wall or hung from ceilings with some simple clips and ‘S’-hooks. We can add Hook & Loop to graphic rails and even add colour powder coating to the Aluminium components in any standard RAL colour.Banners can also be double-sided allowing for a separate graphic to be mounted on the reverse of the display. For most systems, the second graphic will fit into the same carry case as the main display giving you twice the display area for only about a 30% increase in weight.

Highly adaptable
Double sided displays
Stunning Printed Fabric Graphics

We have searched for a method of printing on textiles which produces the highest quality results… showing high resolution, detailed images in vibrant and bright colour.This quality can be achieved by using dye sublimation printing methods where small details can be re-produced on fabric. The vibrant colour is produced as the dye is chemically bonded to the fabric surface and does not ‘soak’ through.
This also means that the fabric is crease resistant, is not stiff, and is machine washable.Using our snap-lock rails, the graphics are also easily replaced by hand if required in the future. This is also a huge environmental and economical benefit, as banner hardware is reused and new graphics are easy to package and courier.

Easy change graphics
System in Detail & Add Accessories
More information on:
The System in Detail